Vendor: fedoraproject
A use-after-free vulnerability was found in the cyttsp4_core driver in the Linux kernel. This issue occurs in the device cleanup routine due to a possible rearming of the watchdog_timer from the workqueue. This could allow a local user to crash the system, causing a denial of service.
In the Linux kernel, the following vulnerability has been resolved: btrfs: make sure that WRITTEN is set on all metadata blocks We previously would call btrfs_check_leaf() if we had the check integrity code enabled, which meant that we could only run the extended leaf checks if we had WRITTEN set on the header flags. This leaves a gap in our checking, because we could end up with corruption on disk where WRITTEN isn't set on the leaf, and then the extended leaf checks don't get run which we rely on to validate all of the item pointers to make sure we don't access memory outside of the extent buffer. However, since 732fab95abe2 ("btrfs: check-integrity: remove CONFIG_BTRFS_FS_CHECK_INTEGRITY option") we no longer call btrfs_check_leaf() from btrfs_mark_buffer_dirty(), which means we only ever call it on blocks that are being written out, and thus have WRITTEN set, or that are being read in, which should have WRITTEN set. Add checks to make sure we have WRITTEN set appropriately, and then make sure __btrfs_check_leaf() always does the item checking. This will protect us from file systems that have been corrupted and no longer have WRITTEN set on some of the blocks. This was hit on a crafted image tweaking the WRITTEN bit and reported by KASAN as out-of-bound access in the eb accessors. The example is a dir item at the end of an eb. [2.042] BTRFS warning (device loop1): bad eb member start: ptr 0x3fff start 30572544 member offset 16410 size 2 [2.040] general protection fault, probably for non-canonical address 0xe0009d1000000003: 0000 [#1] PREEMPT SMP KASAN NOPTI [2.537] KASAN: maybe wild-memory-access in range [0x0005088000000018-0x000508800000001f] [2.729] CPU: 0 PID: 2587 Comm: mount Not tainted 6.8.2 #1 [2.729] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 [2.621] RIP: 0010:btrfs_get_16+0x34b/0x6d0 [2.621] RSP: 0018:ffff88810871fab8 EFLAGS: 00000206 [2.621] RAX: 0000a11000000003 RBX: ffff888104ff8720 RCX: ffff88811b2288c0 [2.621] RDX: dffffc0000000000 RSI: ffffffff81dd8aca RDI: ffff88810871f748 [2.621] RBP: 000000000000401a R08: 0000000000000001 R09: ffffed10210e3ee9 [2.621] R10: ffff88810871f74f R11: 205d323430333737 R12: 000000000000001a [2.621] R13: 000508800000001a R14: 1ffff110210e3f5d R15: ffffffff850011e8 [2.621] FS: 00007f56ea275840(0000) GS:ffff88811b200000(0000) knlGS:0000000000000000 [2.621] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [2.621] CR2: 00007febd13b75c0 CR3: 000000010bb50000 CR4: 00000000000006f0 [2.621] Call Trace: [2.621] <TASK> [2.621] ? show_regs+0x74/0x80 [2.621] ? die_addr+0x46/0xc0 [2.621] ? exc_general_protection+0x161/0x2a0 [2.621] ? asm_exc_general_protection+0x26/0x30 [2.621] ? btrfs_get_16+0x33a/0x6d0 [2.621] ? btrfs_get_16+0x34b/0x6d0 [2.621] ? btrfs_get_16+0x33a/0x6d0 [2.621] ? __pfx_btrfs_get_16+0x10/0x10 [2.621] ? __pfx_mutex_unlock+0x10/0x10 [2.621] btrfs_match_dir_item_name+0x101/0x1a0 [2.621] btrfs_lookup_dir_item+0x1f3/0x280 [2.621] ? __pfx_btrfs_lookup_dir_item+0x10/0x10 [2.621] btrfs_get_tree+0xd25/0x1910 [ copy more details from report ]
In the Linux kernel, the following vulnerability has been resolved: dyndbg: fix old BUG_ON in >control parser Fix a BUG_ON from 2009. Even if it looks "unreachable" (I didn't really look), lets make sure by removing it, doing pr_err and return -EINVAL instead.
Because of a logical error in XSA-407 (Branch Type Confusion), the mitigation is not applied properly when it is intended to be used. XSA-434 (Speculative Return Stack Overflow) uses the same infrastructure, so is equally impacted. For more details, see: https://xenbits.xen.org/xsa/advisory-407.html https://xenbits.xen.org/xsa/advisory-434.html
Unlike 32-bit PV guests, HVM guests may switch freely between 64-bit and other modes. This in particular means that they may set registers used to pass 32-bit-mode hypercall arguments to values outside of the range 32-bit code would be able to set them to. When processing of hypercalls takes a considerable amount of time, the hypervisor may choose to invoke a hypercall continuation. Doing so involves putting (perhaps updated) hypercall arguments in respective registers. For guests not running in 64-bit mode this further involves a certain amount of translation of the values. Unfortunately internal sanity checking of these translated values assumes high halves of registers to always be clear when invoking a hypercall. When this is found not to be the case, it triggers a consistency check in the hypervisor and causes a crash.
In the Linux kernel, the following vulnerability has been resolved: firewire: nosy: ensure user_length is taken into account when fetching packet contents Ensure that packet_buffer_get respects the user_length provided. If the length of the head packet exceeds the user_length, packet_buffer_get will now return 0 to signify to the user that no data were read and a larger buffer size is required. Helps prevent user space overflows.
In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: once more fix the call oder in amdgpu_ttm_move() v2 This reverts drm/amdgpu: fix ftrace event amdgpu_bo_move always move on same heap. The basic problem here is that after the move the old location is simply not available any more. Some fixes were suggested, but essentially we should call the move notification before actually moving things because only this way we have the correct order for DMA-buf and VM move notifications as well. Also rework the statistic handling so that we don't update the eviction counter before the move. v2: add missing NULL check
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: l2cap: fix null-ptr-deref in l2cap_chan_timeout There is a race condition between l2cap_chan_timeout() and l2cap_chan_del(). When we use l2cap_chan_del() to delete the channel, the chan->conn will be set to null. But the conn could be dereferenced again in the mutex_lock() of l2cap_chan_timeout(). As a result the null pointer dereference bug will happen. The KASAN report triggered by POC is shown below: [ 472.074580] ================================================================== [ 472.075284] BUG: KASAN: null-ptr-deref in mutex_lock+0x68/0xc0 [ 472.075308] Write of size 8 at addr 0000000000000158 by task kworker/0:0/7 [ 472.075308] [ 472.075308] CPU: 0 PID: 7 Comm: kworker/0:0 Not tainted 6.9.0-rc5-00356-g78c0094a146b #36 [ 472.075308] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu4 [ 472.075308] Workqueue: events l2cap_chan_timeout [ 472.075308] Call Trace: [ 472.075308] <TASK> [ 472.075308] dump_stack_lvl+0x137/0x1a0 [ 472.075308] print_report+0x101/0x250 [ 472.075308] ? __virt_addr_valid+0x77/0x160 [ 472.075308] ? mutex_lock+0x68/0xc0 [ 472.075308] kasan_report+0x139/0x170 [ 472.075308] ? mutex_lock+0x68/0xc0 [ 472.075308] kasan_check_range+0x2c3/0x2e0 [ 472.075308] mutex_lock+0x68/0xc0 [ 472.075308] l2cap_chan_timeout+0x181/0x300 [ 472.075308] process_one_work+0x5d2/0xe00 [ 472.075308] worker_thread+0xe1d/0x1660 [ 472.075308] ? pr_cont_work+0x5e0/0x5e0 [ 472.075308] kthread+0x2b7/0x350 [ 472.075308] ? pr_cont_work+0x5e0/0x5e0 [ 472.075308] ? kthread_blkcg+0xd0/0xd0 [ 472.075308] ret_from_fork+0x4d/0x80 [ 472.075308] ? kthread_blkcg+0xd0/0xd0 [ 472.075308] ret_from_fork_asm+0x11/0x20 [ 472.075308] </TASK> [ 472.075308] ================================================================== [ 472.094860] Disabling lock debugging due to kernel taint [ 472.096136] BUG: kernel NULL pointer dereference, address: 0000000000000158 [ 472.096136] #PF: supervisor write access in kernel mode [ 472.096136] #PF: error_code(0x0002) - not-present page [ 472.096136] PGD 0 P4D 0 [ 472.096136] Oops: 0002 [#1] PREEMPT SMP KASAN NOPTI [ 472.096136] CPU: 0 PID: 7 Comm: kworker/0:0 Tainted: G B 6.9.0-rc5-00356-g78c0094a146b #36 [ 472.096136] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu4 [ 472.096136] Workqueue: events l2cap_chan_timeout [ 472.096136] RIP: 0010:mutex_lock+0x88/0xc0 [ 472.096136] Code: be 08 00 00 00 e8 f8 23 1f fd 4c 89 f7 be 08 00 00 00 e8 eb 23 1f fd 42 80 3c 23 00 74 08 48 88 [ 472.096136] RSP: 0018:ffff88800744fc78 EFLAGS: 00000246 [ 472.096136] RAX: 0000000000000000 RBX: 1ffff11000e89f8f RCX: ffffffff8457c865 [ 472.096136] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff88800744fc78 [ 472.096136] RBP: 0000000000000158 R08: ffff88800744fc7f R09: 1ffff11000e89f8f [ 472.096136] R10: dffffc0000000000 R11: ffffed1000e89f90 R12: dffffc0000000000 [ 472.096136] R13: 0000000000000158 R14: ffff88800744fc78 R15: ffff888007405a00 [ 472.096136] FS: 0000000000000000(0000) GS:ffff88806d200000(0000) knlGS:0000000000000000 [ 472.096136] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 472.096136] CR2: 0000000000000158 CR3: 000000000da32000 CR4: 00000000000006f0 [ 472.096136] Call Trace: [ 472.096136] <TASK> [ 472.096136] ? __die_body+0x8d/0xe0 [ 472.096136] ? page_fault_oops+0x6b8/0x9a0 [ 472.096136] ? kernelmode_fixup_or_oops+0x20c/0x2a0 [ 472.096136] ? do_user_addr_fault+0x1027/0x1340 [ 472.096136] ? _printk+0x7a/0xa0 [ 472.096136] ? mutex_lock+0x68/0xc0 [ 472.096136] ? add_taint+0x42/0xd0 [ 472.096136] ? exc_page_fault+0x6a/0x1b0 [ 472.096136] ? asm_exc_page_fault+0x26/0x30 [ 472.096136] ? mutex_lock+0x75/0xc0 [ 472.096136] ? mutex_lock+0x88/0xc0 [ 472.096136] ? mutex_lock+0x75/0xc0 [ 472.096136] l2cap_chan_timeo ---truncated---
In the Linux kernel, the following vulnerability has been resolved: Bluetooth: Fix use-after-free bugs caused by sco_sock_timeout When the sco connection is established and then, the sco socket is releasing, timeout_work will be scheduled to judge whether the sco disconnection is timeout. The sock will be deallocated later, but it is dereferenced again in sco_sock_timeout. As a result, the use-after-free bugs will happen. The root cause is shown below: Cleanup Thread | Worker Thread sco_sock_release | sco_sock_close | __sco_sock_close | sco_sock_set_timer | schedule_delayed_work | sco_sock_kill | (wait a time) sock_put(sk) //FREE | sco_sock_timeout | sock_hold(sk) //USE The KASAN report triggered by POC is shown below: [ 95.890016] ================================================================== [ 95.890496] BUG: KASAN: slab-use-after-free in sco_sock_timeout+0x5e/0x1c0 [ 95.890755] Write of size 4 at addr ffff88800c388080 by task kworker/0:0/7 ... [ 95.890755] Workqueue: events sco_sock_timeout [ 95.890755] Call Trace: [ 95.890755] <TASK> [ 95.890755] dump_stack_lvl+0x45/0x110 [ 95.890755] print_address_description+0x78/0x390 [ 95.890755] print_report+0x11b/0x250 [ 95.890755] ? __virt_addr_valid+0xbe/0xf0 [ 95.890755] ? sco_sock_timeout+0x5e/0x1c0 [ 95.890755] kasan_report+0x139/0x170 [ 95.890755] ? update_load_avg+0xe5/0x9f0 [ 95.890755] ? sco_sock_timeout+0x5e/0x1c0 [ 95.890755] kasan_check_range+0x2c3/0x2e0 [ 95.890755] sco_sock_timeout+0x5e/0x1c0 [ 95.890755] process_one_work+0x561/0xc50 [ 95.890755] worker_thread+0xab2/0x13c0 [ 95.890755] ? pr_cont_work+0x490/0x490 [ 95.890755] kthread+0x279/0x300 [ 95.890755] ? pr_cont_work+0x490/0x490 [ 95.890755] ? kthread_blkcg+0xa0/0xa0 [ 95.890755] ret_from_fork+0x34/0x60 [ 95.890755] ? kthread_blkcg+0xa0/0xa0 [ 95.890755] ret_from_fork_asm+0x11/0x20 [ 95.890755] </TASK> [ 95.890755] [ 95.890755] Allocated by task 506: [ 95.890755] kasan_save_track+0x3f/0x70 [ 95.890755] __kasan_kmalloc+0x86/0x90 [ 95.890755] __kmalloc+0x17f/0x360 [ 95.890755] sk_prot_alloc+0xe1/0x1a0 [ 95.890755] sk_alloc+0x31/0x4e0 [ 95.890755] bt_sock_alloc+0x2b/0x2a0 [ 95.890755] sco_sock_create+0xad/0x320 [ 95.890755] bt_sock_create+0x145/0x320 [ 95.890755] __sock_create+0x2e1/0x650 [ 95.890755] __sys_socket+0xd0/0x280 [ 95.890755] __x64_sys_socket+0x75/0x80 [ 95.890755] do_syscall_64+0xc4/0x1b0 [ 95.890755] entry_SYSCALL_64_after_hwframe+0x67/0x6f [ 95.890755] [ 95.890755] Freed by task 506: [ 95.890755] kasan_save_track+0x3f/0x70 [ 95.890755] kasan_save_free_info+0x40/0x50 [ 95.890755] poison_slab_object+0x118/0x180 [ 95.890755] __kasan_slab_free+0x12/0x30 [ 95.890755] kfree+0xb2/0x240 [ 95.890755] __sk_destruct+0x317/0x410 [ 95.890755] sco_sock_release+0x232/0x280 [ 95.890755] sock_close+0xb2/0x210 [ 95.890755] __fput+0x37f/0x770 [ 95.890755] task_work_run+0x1ae/0x210 [ 95.890755] get_signal+0xe17/0xf70 [ 95.890755] arch_do_signal_or_restart+0x3f/0x520 [ 95.890755] syscall_exit_to_user_mode+0x55/0x120 [ 95.890755] do_syscall_64+0xd1/0x1b0 [ 95.890755] entry_SYSCALL_64_after_hwframe+0x67/0x6f [ 95.890755] [ 95.890755] The buggy address belongs to the object at ffff88800c388000 [ 95.890755] which belongs to the cache kmalloc-1k of size 1024 [ 95.890755] The buggy address is located 128 bytes inside of [ 95.890755] freed 1024-byte region [ffff88800c388000, ffff88800c388400) [ 95.890755] [ 95.890755] The buggy address belongs to the physical page: [ 95.890755] page: refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff88800c38a800 pfn:0xc388 [ 95.890755] head: order:3 entire_mapcount:0 nr_pages_mapped:0 pincount:0 [ 95.890755] ano ---truncated---
In the Linux kernel, the following vulnerability has been resolved: r8169: fix LED-related deadlock on module removal Binding devm_led_classdev_register() to the netdev is problematic because on module removal we get a RTNL-related deadlock. Fix this by avoiding the device-managed LED functions. Note: We can safely call led_classdev_unregister() for a LED even if registering it failed, because led_classdev_unregister() detects this and is a no-op in this case.